How to Check and Test the Tower Crane Reducer After Assembly?

As a Tower Crane Manufacturer, share with you. After the assembly of the Custom Tower Crane reducer is completed, before the upper and lower boxes are fastened and the coupling bolts are tightened, check whether the through-hole gland of the reducer is against the rolling bearing jacket and the upper and lower sub-box surfaces for clearance. When the gap is large, grease should be applied to the inner wall of the bearing and all bolts should be tightened to avoid deformation and rapid destruction of the rolling bearing jacket when the coupling bolts are tightened.
8 T Top kit Tower Crane
The sign of good installation quality of the rolling bearing is that all parts are cleaned, there is no dirt in the box, and the transmission part can be rotated smoothly by gently turning the hand by hand, without jamming, impact and noise; the temperature rise of long-term operation does not exceed 80 degrees. If defects such as jamming, noise and excessive temperature rise are found, the trial operation should be stopped immediately, the fault should be checked and eliminated, and reinstalled.
When assembling the reducer, check the meshing quality of the gear pair. It is required that the flank clearance is appropriate, the contact surface is large and uniform, and there is no noise and impact sound.
The contact marks on the gear meshing surface should be no less than 60% of the tooth height and no less than 50% of the tooth width and should be evenly distributed. The uniformity of the gear meshing surface along the tooth height depends on the processing quality of the gearbox, the parallelism of the shaft, the allowable inclination of the shaft and the deflection of the gear tooth direction. The parallelism of the shaft can be measured with a rod vernier caliper.
After the reducer is assembled, it needs to be tested and then run-in test. Before the running-in test, clean light oil should be injected into the reducer. During the running-in trial operation, it should run at full speed in forwarding and reverse directions, and it can be confirmed that there is no strong noise, knocking and periodic noise during gear operation, oil temperature and bearing heating not exceeding 80 degrees, and no oil leakage at the seal and flange joint 1. The contact mark is not less than the specified standard.
After the running-in trial operation is completed, the lubricating oil in the box should be completely dumped and thoroughly washed with kerosene, and no debris such as abrasive debris can be left in the gearbox. After that, new lubricant can be injected and run for a period of time so that all parts in the tank is covered with lubricant.
Our company also has 8 T Top kit Tower Crane for sale, please contact us.

评论

发表评论

此博客中的热门博文

Crane History

图片
As a  Luffing Tower Crane Supplier , let's share with you the history of the crane. In 10 BC, the ancient Roman architect Vitruvius described a lifting device in his architectural manual. The machine has a mast with a pulley on the top of the pole, the position of the mast is fixed by the pulling rope, and the cable passing through the pulley is pulled by the winch to lift the heavy object. Some overweight machines can use two masts to form a herringbone shape, moving the lifting object laterally, but the amplitude is small and the operation is very difficult. In the 15th century, Italy invented  Luffing jib Tower Cranes  to solve this problem. The crane has a sloping cantilever with a pulley on the top of the arm that can be lifted and rotated. However, until the 18th century, all kinds of lifting appliances used by human beings were powered by human and animal power, and they were limited in terms of lifting the weight, the scope of use and work efficiency. In th...
阅读全文

Introduction to Top Kit Tower Crane

图片
Topless Tower Crane is the most commonly used lifting equipment on construction sites. It is used for the construction of steel bars, rafts, concrete, steel pipes, etc. in a section of the  Tower Crane Mast Section . Raw materials. Tower cranes are essential equipment on the construction site. As a  Tower Crane Spare Parts Factory , let's give you a detailed explanation. Top Kit Tower Crane The function of the Topless Tower Crane is to withstand the upper load from the boom puller and the balance arm drawstring and transmit it to the tower structure directly through the turntable through the structural components of the swing tower, turntable, and seat. The top of the self-lifting tower has a truncated cone type, a forwardly inclined or a backward inclined truncated cone type, a herringbone type, and a diagonal bracket type. All the upper slewing tower cranes need to be balanced, and their function is to support the balance weight, which is used to form the balance mo...
阅读全文

Do you know the Regulation of Tower Crane Lifting Height?

图片
As a  10 T Top kit Tower Crane Wholesale , share with you. Lifting height is also called hook height, which is the vertical distance from the concrete foundation surface of the tower crane (or the top surface of the walking track) to the hook. For trolley cranes, the maximum lifting height is immutable. For pitch cranes, the lifting height varies with different amplitudes. At the minimum amplitude, the lifting height can be several dozens higher than the tower tip meters, so the tower crane with pitch amplitude has an advantage in lifting height. Top Kit Tower Crane Tower crane lifting height includes two parameters, one is the lifting height when the tower crane is installed at a free height, and the other is the maximum lifting height when the tower crane is attached. The tower crane does not need to be attached when the free height is installed. The general tower crane It can reach 40 meters, which can meet the needs of buildings below small high-rises. In order to pr...
阅读全文